項目一設計開發光照度檢測控制器... 1
任務一設計制作流水燈.............................2
任務描述..............................................................................2
相關知
識
一、單片機與嵌入式系統............................................2
二、單片機的發展史......................................................4
三、STM8L051F3單片機概述..............................4
四、STM8L051F3.基礎知識介紹.........................6
五、TTL電平邏輯........................................................... 8
六、通用I/
O
端口（GPIO）...................................
. 8
任務實施......................................................................................10
任務拓展......................................................................................20
任務二設計制作按鍵控制LED
燈...........21
任務描述......................................................................................21
相關知
識
一、中斷................................................................................21
二、按鍵及其分類...........................................................22
任務實施.......................................................................................23
任務拓展.......................................................................................28
任務三光照度檢測控制系統....................29
二、光敏傳感器...............................................................31
三、A/D轉換器...............................................................32
任務實施......................................................................................34
任務拓展......................................................................................41
思考與問答....................................................41
目錄
項目二設計制作智能電子鐘.......42
任務一設計制作字符顯示器....................43
任務描述...........................................................................43
相關知
識
一、IIC.基礎知識............................................................43
二、顯示器件簡介..........................................................50
三、OLED.時序的IIC.配置...................................51
四、OLED.IIC
接口連接原理圖............................52
任務實施...........................................................................53
任務拓展...........................................................................68
任務二設計制作智能電子鐘....................68
任務描述...........................................................................68
相關知識
一、定時器
計數器......................................................68
二、RTC.概述...................................................................70
任務實施...........................................................................74
任務拓展........................................................................101
項目三設計開發環境紫外線監測器...102
任務一設計開發環境溫濕度檢測器.......103
任務描述........................................................................103
相關知識........................................................................103
任務實施........................................................................105
任務拓展........................................................................115
任務二設計開發紫外線監測顯示器.......115
任務描述........................................................................115
相關知
識
一、紫外線對人體的影響.......................................115
二、紫外線檢測原理..................................................116
三、紫外線傳感器電路解析..................................117
四、紫外線傳感代碼解析.......................................118
任務實施........................................................................120
任務拓展........................................................................132
思考與問答..................................................132
項目四設計開發基于藍牙的可穿戴
人體體溫監測器..........133
任務一設計開發人體體溫監測器..........134
任務描述........................................................................134
相關知
識
一、體溫信息采集的價值............................134
二、非接觸式體溫傳感器原理.................134
三、溫度采集電路解析.................................135
四、溫度傳感數據采集代碼解析............136
任務實施........................................................................138
任務拓展........................................................................148
任務二設計開發基于藍牙的人體體溫
..............監測器
.
........................................................148
任務描述........................................................................148
相關知識
一、通信的基本概念.......................................148
二、STM8L的USART.通信...................151
三、藍牙模塊簡介............................................154
任務實施........................................................................157
任務拓展........................................................................171
思考與問答..................................................171
項目五可穿戴設備綜合實訓運動
輔助設備的設計..........172
任務一設計開發人體心率檢測器..........172
任務描述........................................................................173
相關知
識
一、心率采集信息價值.............................................173
二、心率傳感器及原理............................................174
三、心率傳感器電路解析.......................................175
四、心率傳感代碼解析.............................................175
任務實施........................................................................177
任務拓展........................................................................190
任務二設計開發運動計步器..................190
任務描述........................................................................190
相關知
識
一、陀螺儀的發展歷程.............................................191
二、MPU6050傳感器的使用..............................192
三、步伐識別算法........................................................193
四、運動傳感代碼解析.............................................195
任務實施........................................................................196
任務拓展........................................................................217
思考與問答..................................................217
附錄AIAR的安裝及配置........218
一、軟件下載.............................................................218
二、軟件安裝.............................................................219
三、軟件的使用和配置.......................................227
四、STM8L051F3工程創建..........................231
附錄Ｂ圖形符號對照表..........236
參考文獻........................ 237
書單推薦
